1. Connect the handset to SetuPhone with handset cord.

2. Plug one end of telephone cable (RJ-11) into the LINE port on the rear panel of SetuPhone and the other end into a working telephone wall jack.

3. Plug the AC power adaptor provided into an AC outlet and insert the power cord into the connector marked "AC" on the rear panel of the SetuPhone.

4. Lift the handset and listen for the dial tone that indicates the SetuPhone has been installed properly. If you do not hear a dial tone, check that the power adaptor is plugged into a live electrical outlet and that the power cord is pushed securely into the connector.

5. Now SetuPhone is ready for basic configuration.

SetuPhone Modem IP Phone quick configuration

1.For configuring of SetuPhone, press *123* and terminate by a # button

2. You will be asked for a password. Enter the password. (Default password is 12345)

3. If wrong password is entered, the phone will prompt that the password is incorrect and will ask the user to enter again

4. If password is correct, phone will prompt the main menu.

5. Press 1 if you want to configure the ISP parameters, 2 for calling card parameters, 3 for extended menu, 4 for listening to configured parameters, 5 to save and quit. ISP information

6. If you press 1 at the main menu, the phone will prompt "ISP Phone Number is xxxxx. Press '1' to edit '2' to skip"

7. Press '1' to edit the ISP phone number. If you press '1', the phone will prompt, "Please enter the ISP Phone Number and terminate by a # button" Now enter the ISP Phone Number using the keypad. After you finish entering the parameter, press # button.

8. The phone will prompt, "You entered xxxxx. Press '1' to accept, '2' to re-enter" Press '1' to accept the parameter, or if you want to re-enter, press '2' .By pressing '2' we go back to step 7.

9. Once you accept the ISP phone number, the phone will prompt with the ISP Username. "The ISP Username is xxxx. Press '1' to edit, '2' to skip". Follow the same procedure as that for ISP Phone Number

10. Once you change or skip the ISP username, phone will prompt, "The ISP password is xxxxx. Press '1' to edit '2' to skip". Again, follow the same procedure as that for ISP Phone Number. After the ISP password is configured, the phone will play main menu again

Keep in mind : You can't enter the special characters or alphabets while entering the ISP Phone Number. Those modes are disabled for ISP Phone Number entry.

Calling card Information

11. On pressing '2' at the main menu(Password- setu), the phone will prompt, "calling card userID is xxxx. Press '1' to edit, '2' to skip" Press '1' if the userID is to be changed, else press '2' to skip to the next parameter.

12. If '1' is pressed, the phone will prompt, "Please enter the calling card userID and terminate by a # button" Now enter the calling card userID using the keypad. After you finish entering the parameter, terminate by a # button

13. The Phone will prompt, "You entered xxxx. Press '1' to accept, '2' to re-enter" Press '1' for accepting the parameter, or '2' for re-entering the same.

14. After the calling card user ID is configured, the phone will prompt, "The calling card Password is xxxx. Press '1' to edit, '2' to skip" Configure this as same as that for calling card user ID.

15. After this the phone will prompt for VoIP server address, "VoIP server address is xxx.xxx.xxx.xxx press '1' to edit, '2' to skip" Press '1' to change the server address. If the value entered is improper IP address, the phone will prompt with "The parameter you have entered is incorrect, Press '1' to edit, '2' to skip". After the server address is configured, the phone plays the main menu.

Extended configuration

16. Pressing '3' at the main menu, phone plays the extended configuration menu.

17. In this menu, the user can change the configuration password, software upgrade server address , country, language, service provider.

18. Press '1' to change the configuration password. The phone will prompt, "The configuration password is xxxx. Press '1' to edit '2' to skip" Press '1' to change the configuration password, or '2' to go back to the extended menu.

19. Similarly you can configure the other parameters in the extended menu.

Review the configured parameters

20. Press '4' at main menu for listening to the configured parameters

Save and Exit

21. You have to press '5' at the main menu to save the configured parameters. If power goes off during configuration or you exit the configuration, the changed parameters will not be saved onto the flash.

Entering information through keypad

1. For entering a digit, press the digit key once

2. For entering an alphabet, press the digit keys more than once within short interval. If you press the key 2 times, the first alphabet marked on the key will be accepted as input.

For ex: Digit key 2 has three alphabets on it. (a,b,c) If 2 is pressed twice the phone will accept the input as 'a'. If digit key '2' is pressed thrice, 'b' is accepted. If 2 is pressed four times, 'c' is accepted. If any key is pressed more number of times, the last alphabet will be accepted.

The alphabets, by default will be in lowercase.

3. For entering in uppercase, the shift button has to be switched ON and then the alphabet has to be entered.

4. For entering special characters, press the Dial up button and then the corresponding digit key. For backspace press dial up button and then digit key '0', for '@' press dial up button and then digit key '1' and so on. The keys 2 to 8 correspond to '.', '-','_','$','&','/',':' respectively.

Entering Special Characters

Press DIAL UP button and then press the corresponding key mentioned in table below to enter special characters.

Note: Backspace can be used to delete the unwanted character. It will delete the last entered character.

Examples:

• To enter @, press DIAL UP followed by key 1.
• To enter ., press DIAL UP followed by key 2.
• To delete the last character, press DIAL UP followed by key 0.